Detailed description
working principle:
SZG series double cone rotating vacuum drier has double
cone rotating tank, the tank in a vacuum state, to the jacket into a
thermal oil or hot water heating, heat through the tank wall contact
with the wet material. Evaporation of water vapor or other gases after
wet material absorbs heat through vacuum exhaust pipe is pumped. Since
the tank body in a vacuum state, and the rotating of tank so that the
material constant up and down, inside and outside the flip, it
accelerated the drying rate of materials, improve drying rate, to
achieve uniform drying purposes.
Process Equipment Demo:
Features:
Because it is dried under vacuum, at a lower temperature has a
higher rate of increase than the average rate of 2 times the drying
equipment, energy saving, high thermal efficiency, especially for
heat-sensitive materials dry and easy oxide material.
The machine advanced design, simple internal structure, easy to clean, discharge all raw material, simple operation.
Closed drying, the product no leakage, no pollution, suitable for intense stimulation, dried toxic materials.
Blended in a rotating drying, the material can be dried to a low
moisture content (≤0.5%), and good uniformity, suitable for different
material requirements.
Equipment, compact structure, small footprint, easy operation, reduce labor intensity, labor-saving.
Users can choose stepless (1-10 rev / min) and a level speed
(6-10 rev / min), to facilitate high-speed drying capacity and adapt to
different requirements.
Installation diagram:
Applications:
This machine is suitable for powder, vacuum drying and mixing
granular material medicine, food, chemical industry, especially suitable
for drying by the following requirements:
1, can not accept the high temperature heat-sensitive materials
2, the need to recycle solvents and toxic gases Material
3, easily oxidized, hazardous materials
4, there is a crystalline material requirements
5 requires a very low residual volatile matter content of the material
Schematic:
Technical specifications:
specification | 100 | 350 | 500 | 750 | 1000 | 1500 | 2000 | 3500 | 4500 |
Tank volume (L) | 100 | 350 | 500 | 750 | 1000 | 1500 | 2000 | 3500 | 4500 |
Loading volume (L) | ≤50 | ≤175 | ≤250 | ≤375 | ≤500 | ≤750 | ≤1000 | ≤1750 | ≤2250 |
Speed (rpm) | 3 to 13 |
Motor power (kw) | 0.75 | 1.1 | 1.5 | 2 | 3 | 3 | 4 | 5.5 | 7.5 |
Covers an area of
length × width (mm) | 2160×800 | 2260×800 | 2350×800 | 2560×1000 | 2860×1300 | 3060×1300 | 3260×1400 | 3760×1800 | 3960×2000 |
Rotating height (h) | 1750 | 2100 | 2250 | 2490 | 2800 | 2940 | 2990 | 3490 | 4100 |
Tank design pressure (MPa) | -0.1 ~ 0.15 |
Jacket design pressure (MPa) | ≤0.3 |
Working Temperature (℃) | Jacketed tank ≤85 ≤140 |
With a condenser, the vacuum pump models, power (kw) | 2X-15A
2kw | 2X-15A
2kw | 2X-30A
3kw | 2X-30A
3kw | 2X-70A
5.5kw | JZJX300-8
7KW | JZJX300-4
9.5kw | JZJX600-8
11kW | JZJX600-4
20.5kw |
When not in condenser vacuum pump model, power (kw) | SK-0.4
1.5kw | SK-0.4
1.5kw | SK-0.8
2.2kw | SK-2.7B
4kw | SK-2.7B
4KW | SK-3
5.5KW | SK-6
11KW | SK-6
11KW | SK-9
15KW |
Weight (kg) | 800 | 1100 | 1200 | 1500 | 2800 | 3300 | 3600 | 6400 | 7500 |
Note: for large volume change before and after
drying the material, which may be appropriate to increase the loading
factor, or reduced, the maximum loading volume can not come into contact
with the bottom surface of the vacuum tube. Motor according to user
requirements matching speed motor, speed 0 ~ 6r.pm; above technical
parameters of materials according to the proportion of 0.6g / cm3
computing, such as more than, to be mentioned when ordering; user
certificate for pressure vessel, to be mentioned when ordering ; such as
the use of glass-lined interior materials, to be mentioned when
ordering; materials, such as flammable and explosive, when orders need
to clear that otherwise is strictly prohibited.
Ordering Information:
1, sub-heating hot water, oil heating two forms.
2, please indicate the material can withstand temperatures or dryer
temperature when ordering, so that the factory of your choice or
provide heat.
3, drying the adhesive material, the factory will be in the tank specially designed "copy board" structure.
4, Annex vacuum drying system involved, I plant can provide users with installation, please indicate in the order.
5, the factory can provide special requirements of users design, manufacture and installation.
Previous ：GLZ series vacuum ribbon dryer
Next：YZG / FZG Series Vacuum Dryer
